How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
What are your thoughts on How to Install a Bathtub?
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is also a moderately difficult project. If the old tub is easily available, the job can move rapidly; if you have to open a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Ensure you have certified yourself for the work and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is much better to think about utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you mount a brand-new bath tub in your washroom if you have actually already purchased a new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist should comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub until the level checks out degree.
To install faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the supply of water and check all joints and new pipework for leakages as well as tighten them if needed. Fill up the tub and also examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has been made use of at the very least once as this will resolve it right into its final placement.
Planning for the Setup
First of all, the supporting structure provided with the bath should be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to stop stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about A Step-by-Step Guide to Installing a Bathtub? Post a review further down. We'd be glad to listen to your thinking about this content. We hope to see you back again soon. Appreciated our content? Please share it. Let others locate it. Thank you for taking the time to read it.
Book Your Installation Report this page